« previous next »
Pages: [1]   Go Down

Author Topic: shifter inspection cover  (Read 837 times)

0 Members and 1 Guest are viewing this topic.

melbill

  • Guest
shifter inspection cover
« on: April 10, 2010, 06:42:23 PM »
I am removing the cover from over the transmission and transfer case inside my 95 YJ.  I don't know the proper name for it, sorry.  There are 2 covers a smaller one and  larger one around the 2 shifter levers.  When I lift up on them there seems to be a gasket or sealant between the covers and the floor panel. Can out the sealant material? Can it be replaced with RTV, another sealant, or is a gasket the right way to go, and if so where can I find one.  I want to be sure to seal this correctly as I don't want to let water in there.

Thanks

Bill   
Logged

Offline sharpxmen

  • Chief Squirrel Blower®
  • Member
  • *
  • Posts: 7093
Re: shifter inspection cover
« Reply #1 on: April 10, 2010, 07:40:46 PM »
Quote from: melbill on April 10, 2010, 06:42:23 PM
I am removing the cover from over the transmission and transfer case inside my 95 YJ.  I don't know the proper name for it, sorry.  There are 2 covers a smaller one and  larger one around the 2 shifter levers.  When I lift up on them there seems to be a gasket or sealant between the covers and the floor panel. Can out the sealant material? Can it be replaced with RTV, another sealant, or is a gasket the right way to go, and if so where can I find one.  I want to be sure to seal this correctly as I don't want to let water in there.

Thanks

Bill   

that sealant is not for water, is so you don't get fumes inside. You can use RTV but that will make it hard to take off, there is a body panel sealer just like that one there that comes in strips (round or even flat i think) and you can just add where you're missing it or replace the whole thing.
Logged
'95 YJ, NSG370 6spd / Hurst shifter, Dana 300 + 4:1 Doubler / tri-stick, Custom skid, Super D35 / Auburn LSD / 4.88, 35x12.5x15 BFG KM2, 64mm t/b, 1.7 RollerRockers, MkVIII e-fan, Dual Diaph Booster
Latest: Corbeau BajaRS heated seats :dance: keeping warm the rear end

Offline FourbangerYJ

  • Servicing Squirrels Since 1995®
  • Member
  • *
  • Posts: 3372
Re: shifter inspection cover
« Reply #2 on: April 10, 2010, 07:51:00 PM »
At the hardware store you can buy some weather stripping that is made for sealing a canopy on a pick up bed. It's sticky on one side only. Or something simular.
Logged
Scott~

Using tools you have not used in a while is like shaking hands with old friends. :nod:

Offline Bounty Hunter

  • Member
  • Posts: 1658
    • http://www.sija.org
Re: shifter inspection cover
« Reply #3 on: April 10, 2010, 09:45:12 PM »
RTV or even clear silicone will work fine.
Logged

Offline dwtaylorpdx

  • Member
  • Posts: 1038
Re: shifter inspection cover
« Reply #4 on: April 10, 2010, 10:54:21 PM »
I like the non hardening stuff, I've had mine off numerous times and its still the original sealer...

Dave
Logged
94 YJ - 2.5 Hesco Cam B&B Ported - AX5 Trans w/Centerforce Dual Friction Clutch - 4" Rough Country Lift W/Skyjacker Shocks - D44 Rear/ARB - D30/ARB - ARB Compressor - Warn M8000 in Custom Bumper - Reunell Rear Bumper - Metalcloak 6" Body Armor Kit - Tuffy Console - 265x85-16 Tires - 2M Radio

melbill

  • Guest
Re: shifter inspection cover
« Reply #5 on: April 11, 2010, 05:47:51 AM »
Thank you all. One of my favorite things about this forum is getting many solutions to the same problem. It makes it best to figure out what will work for each individual in their particular situation.
Logged
Pages: [1]   Go Up
« previous next »