« previous next »
Pages: [1]   Go Down

Author Topic: Starter needs shims?  (Read 606 times)

0 Members and 3 Guests are viewing this topic.

Offline dexetr30

  • 4BangerJP.com® Donator
  • Member
  • *
  • Posts: 1261
  • Aloha Mr. Hand!
Starter needs shims?
« on: December 12, 2007, 06:49:56 PM »
I installed my new starter tonight and it doesn't quite fit. It grinds a bit when turning it over and does not engage into the teeth on the flywheel. Do the 2.5's require the use of a shim? The o.e. starter did not have one. The replacement starter is after-market but looks identical to the o.e.
Logged
02 2.5.L automatic: 4.0L t.b., 4.0l air intake, K&N filter, Scream'n Demon coil, 8.5mm MSD Super Conductor plug wires, Stage 1 Jet Chip, 29" BFG all terrain KO's. Taurus E-fan, Hummer front bumper, Skyjacker high capacity trans pan, 48" hi-lift, Rubi susp w. 3/4" BB.

Jesse-James

  • Guest
Re: Starter needs shims?
« Reply #1 on: December 12, 2007, 06:53:36 PM »
Mine didn't, but I ran into the same problem with my Toronado. Had to shim it back a little.
Logged

Offline dexetr30

  • 4BangerJP.com® Donator
  • Member
  • *
  • Posts: 1261
  • Aloha Mr. Hand!
Re: Starter needs shims?
« Reply #2 on: December 12, 2007, 07:07:20 PM »
Well, I need the Jeep bad tomorrow so I cleaned all the terminals on the o.e. starter with a wire brush and some contact cleaner and reinstalled it for the time being. If I have time tomorrow I'll pick up some shims and give it another go.
Logged
02 2.5.L automatic: 4.0L t.b., 4.0l air intake, K&N filter, Scream'n Demon coil, 8.5mm MSD Super Conductor plug wires, Stage 1 Jet Chip, 29" BFG all terrain KO's. Taurus E-fan, Hummer front bumper, Skyjacker high capacity trans pan, 48" hi-lift, Rubi susp w. 3/4" BB.

Offline oldjeep

  • Member
  • Posts: 1800
    • www.Oldjeep.com
Re: Starter needs shims?
« Reply #3 on: December 13, 2007, 06:15:47 AM »
My 94 has a single shim
Logged
Chuck P
The clowns'? Oh, yeah, the clowns. We fight them too — entire armies, spilling out of Volkswagons. We do our best to fight them off, but they keep sending 'em in!
94 YJ - gone
98 ZJ - sons truck
97 TJ - daughters project

www.oldjeep.com

Offline dexetr30

  • 4BangerJP.com® Donator
  • Member
  • *
  • Posts: 1261
  • Aloha Mr. Hand!
Re: Starter needs shims?
« Reply #4 on: December 13, 2007, 02:49:05 PM »
I took a look at the scrape marks on the flywheel and it looks like I'll only need one as well.
Logged
02 2.5.L automatic: 4.0L t.b., 4.0l air intake, K&N filter, Scream'n Demon coil, 8.5mm MSD Super Conductor plug wires, Stage 1 Jet Chip, 29" BFG all terrain KO's. Taurus E-fan, Hummer front bumper, Skyjacker high capacity trans pan, 48" hi-lift, Rubi susp w. 3/4" BB.
Pages: [1]   Go Up
« previous next »