Author Topic: question regardin TB spacer  (Read 5270 times)

0 Members and 8 Guests are viewing this topic.

Offline andpgud

  • Member
  • Posts: 120
Re: question regardin TB spacer
« Reply #15 on: April 16, 2011, 05:04:27 AM »
What would you say if I would get a stock 4L TB and a 55mm, 1" wide spacer and bore the Intake manifold to 55mm?
How would that work out for the 2.5?
« Last Edit: April 16, 2011, 05:04:57 AM by andpgud »

Offline chardrc

  • Member
  • Posts: 3535
Re: question regardin TB spacer
« Reply #16 on: April 16, 2011, 07:46:53 AM »
I Run a custom TB spacer which is 60mm top side and tapers to 55mm bottom side. Helps keep air pressurized coming in which maintains torque through out the power band. Works for me.

that would be a nozzle which would increase velocity and decrease pressure according to Bernoulli equation (simplification)

take a look at the picture on right side of the wiki link.
http://en.wikipedia.org/wiki/Bernoulli%27s_principle

you have to have the same flow rate through the entire system so when you go to a smaller diameter the velocity has to go up to maintain the flow rate.  Bernoulli equation has velocity, pressure, and gravitational potential terms, in this case (1 inch drop) gravitational potential change is quite small, so for the increase in velocity you lose pressure. 
1990 YJ 4cly, ax5, 2.5 inch BDS lift, 31 MTr\'s,  Powertrax-lockers all around, track-bars removed, boomerang shackles, warn m8000 winch, electric fan. [sold but not forgotten]

2007 jk Rubicon 2dr

Offline andpgud

  • Member
  • Posts: 120
Re: question regardin TB spacer
« Reply #17 on: April 16, 2011, 08:33:53 AM »
So 55mm all the way should do the job?

Offline FourbangerYJ

  • Servicing Squirrels Since 1995®
  • Member
  • *
  • Posts: 3372
Re: question regardin TB spacer
« Reply #18 on: April 16, 2011, 09:01:37 AM »
So 55mm all the way should do the job?

It's more than the stock one so it does gain a bit of performance. The 62-64mm ones even more so.
Scott~

Using tools you have not used in a while is like shaking hands with old friends. :nod:

Offline sharpxmen

  • Chief Squirrel Blower®
  • Member
  • *
  • Posts: 7093
Re: question regardin TB spacer
« Reply #19 on: April 16, 2011, 09:55:03 AM »
these are 64mm




comparison 2.5 vs. 4.0 vs. 64mm



'95 YJ, NSG370 6spd / Hurst shifter, Dana 300 + 4:1 Doubler / tri-stick, Custom skid, Super D35 / Auburn LSD / 4.88, 35x12.5x15 BFG KM2, 64mm t/b, 1.7 RollerRockers, MkVIII e-fan, Dual Diaph Booster
Latest: Corbeau BajaRS heated seats :dance: keeping warm the rear end

quicksand

  • Guest
Re: question regardin TB spacer
« Reply #20 on: April 16, 2011, 11:44:53 AM »
Nice 64s, do you also bore the manifold that big on a 2.5L?

Offline FourbangerYJ

  • Servicing Squirrels Since 1995®
  • Member
  • *
  • Posts: 3372
Re: question regardin TB spacer
« Reply #21 on: April 16, 2011, 12:07:29 PM »
these are 64mm






There are rules against posting PORN PICS here.  :nono: Might have to give you a timeout!  :lol:
Scott~

Using tools you have not used in a while is like shaking hands with old friends. :nod:

Offline sharpxmen

  • Chief Squirrel Blower®
  • Member
  • *
  • Posts: 7093
Re: question regardin TB spacer
« Reply #22 on: April 16, 2011, 01:06:28 PM »
Nice 64s, do you also bore the manifold that big on a 2.5L?

yep, and round the edges under the bore

There are rules against posting PORN PICS here.  :nono: Might have to give you a timeout!  :lol:

fixed, should be gone in a bit
« Last Edit: April 16, 2011, 01:07:34 PM by sharpxmen »
'95 YJ, NSG370 6spd / Hurst shifter, Dana 300 + 4:1 Doubler / tri-stick, Custom skid, Super D35 / Auburn LSD / 4.88, 35x12.5x15 BFG KM2, 64mm t/b, 1.7 RollerRockers, MkVIII e-fan, Dual Diaph Booster
Latest: Corbeau BajaRS heated seats :dance: keeping warm the rear end

Offline andpgud

  • Member
  • Posts: 120
Re: question regardin TB spacer
« Reply #23 on: April 16, 2011, 05:44:45 PM »
I would like to get those photos bakc :(

Offline FourbangerYJ

  • Servicing Squirrels Since 1995®
  • Member
  • *
  • Posts: 3372
Re: question regardin TB spacer
« Reply #24 on: April 16, 2011, 05:49:13 PM »


fixed, should be gone in a bit

You know I was teasing about the Porn bit, right?   :drink: Bring em back.  :lol:
Scott~

Using tools you have not used in a while is like shaking hands with old friends. :nod:

Offline sharpxmen

  • Chief Squirrel Blower®
  • Member
  • *
  • Posts: 7093
Re: question regardin TB spacer
« Reply #25 on: April 16, 2011, 07:36:35 PM »
I would like to get those photos bakc :(

You know I was teasing about the Porn bit, right?   :drink: Bring em back.  :lol:

they're back
'95 YJ, NSG370 6spd / Hurst shifter, Dana 300 + 4:1 Doubler / tri-stick, Custom skid, Super D35 / Auburn LSD / 4.88, 35x12.5x15 BFG KM2, 64mm t/b, 1.7 RollerRockers, MkVIII e-fan, Dual Diaph Booster
Latest: Corbeau BajaRS heated seats :dance: keeping warm the rear end

Offline FourbangerYJ

  • Servicing Squirrels Since 1995®
  • Member
  • *
  • Posts: 3372
Re: question regardin TB spacer
« Reply #26 on: April 16, 2011, 10:27:50 PM »
they're back


Thanks for bringing back the eye candy!  :naughty:  :hump:  ;)
Scott~

Using tools you have not used in a while is like shaking hands with old friends. :nod:

Offline andpgud

  • Member
  • Posts: 120
Re: question regardin TB spacer
« Reply #27 on: April 18, 2011, 04:47:15 AM »
With doing the TB thing and with the spacer, do you get better MPG?

Offline sharpxmen

  • Chief Squirrel Blower®
  • Member
  • *
  • Posts: 7093
Re: question regardin TB spacer
« Reply #28 on: April 18, 2011, 08:26:16 AM »
With doing the TB thing and with the spacer, do you get better MPG?

unlikely, as you get better response and probably drive faster it might get worse. It's more about the way you drive than anything and based on how this would fit your style of driving could go either way.
'95 YJ, NSG370 6spd / Hurst shifter, Dana 300 + 4:1 Doubler / tri-stick, Custom skid, Super D35 / Auburn LSD / 4.88, 35x12.5x15 BFG KM2, 64mm t/b, 1.7 RollerRockers, MkVIII e-fan, Dual Diaph Booster
Latest: Corbeau BajaRS heated seats :dance: keeping warm the rear end