« previous next »
Pages: [1]   Go Down

Author Topic: Measuring to level the TJ  (Read 1729 times)

0 Members and 1 Guest are viewing this topic.

Offline jagular7

  • Member
  • Posts: 987
Measuring to level the TJ
« on: August 23, 2005, 07:24:33 AM »
I've added a winch up front, added ACOS spacer up front, 05 Rubi Unlimited springs all around, 2" rear poly spacer, front RE adjustable track bar, and riser block for the rear track bar. How do I go about measuring my TJ to level it out, or have a slightly nose down attitude?

I currently have the ACOS adjusted to where the top of the front fender and the lower rear side window channel are horizontal. It looks flat but has a wander to it.
Logged
Jagular7
97 SE - Rubbered and locked for fun
94 SE - stock, collecting parts for 37s

Offline Jeffy

  • Administrator
  • Member
  • Posts: 14934
Measuring to level the TJ
« Reply #1 on: August 23, 2005, 07:14:33 PM »
How?  Put a level on a flat part of the body and check it.   Rocker, hood, rear body would be good places.  You will also want to check for lean.
Logged
Youtube Channel: https://www.youtube.com/channel/UCZNlr60GXH5OlKIFrT7P6mg
My Jeep: http://4bangerjp.com/forums/index.php?topic=2783.0
"If the motor car were invented today, there is absolutely no way that any government in the world would let normal members of the public drive one."

Offline Bounty Hunter

  • Member
  • Posts: 1658
    • http://www.sija.org
Measuring to level the TJ
« Reply #2 on: August 24, 2005, 02:22:16 PM »
The wander is generally incorrect caster, or worn steering components.  Got nothing to do with the stance of the jeep.
Logged

Offline jagular7

  • Member
  • Posts: 987
Measuring to level the TJ
« Reply #3 on: August 24, 2005, 07:46:45 PM »
Quote from: "Bounty Hunter"
The wander is generally incorrect caster, or worn steering components.  Got nothing to do with the stance of the jeep.


I didn't mean to finish in the middle, but I had to go (this was at work).
I've adjusted down the ACOS to make it level by using a level on the fender and rear window sill. I didn't use the rocker as it's a bit bubbly (rusty underneath).

As for the wander, I'm not sure if the rear is not aligned with the front and was wondering if this could lead to the Jeep wander? I'm also thinking it could be the steering box itself. When I lower, I adjust the track arm to get as close to making both tires even on the fenders, and adjust the steering to re-center the steering wheel. I don't check the toe or caster. Think lowering it ~3/4-1" is significant to the caster? As for steering components, I do have a new Currie tie rod set to throw on. Just need to get new boots for the ripped ones.

Thanks.
Logged
Jagular7
97 SE - Rubbered and locked for fun
94 SE - stock, collecting parts for 37s

Offline Bounty Hunter

  • Member
  • Posts: 1658
    • http://www.sija.org
Measuring to level the TJ
« Reply #4 on: August 24, 2005, 09:39:41 PM »
Lowering the spring height will reduce caster, increasing wander.  Changing spring height will also alter the toe-in quite a bit and change the amount of wander.  Sounds like you need to get these two in spec after the adjustments.
Logged
Pages: [1]   Go Up
« previous next »