Author Topic: thermostat  (Read 1539 times)

0 Members and 1 Guest are viewing this topic.

andrew383

  • Guest
thermostat
« on: January 24, 2009, 06:44:12 PM »
well the radiator took a dump today and so did the thermostat.so i got a new rad and stat.the stat i got was a 180* one.its about 20* outside rite now and driving it around is a PITA now cause it runs so cold.

what is the factory stat temp??

Offline Jeffy

  • Administrator
  • Member
  • Posts: 14934
Re: thermostat
« Reply #1 on: January 24, 2009, 07:59:44 PM »
195*
Youtube Channel: https://www.youtube.com/channel/UCZNlr60GXH5OlKIFrT7P6mg
My Jeep: http://4bangerjp.com/forums/index.php?topic=2783.0
"If the motor car were invented today, there is absolutely no way that any government in the world would let normal members of the public drive one."

andrew383

  • Guest
Re: thermostat
« Reply #2 on: January 24, 2009, 08:56:14 PM »
dang...im gonna have to block part of the grill tommorrow for the trail ride so i wont get cold  :brick:

RobJ

  • Guest
Re: thermostat
« Reply #3 on: May 19, 2009, 01:50:10 PM »
Thermostats can be bad out of the box. I put in a new long block a few fears ago and went with a Robertshaw stat from Quadratech figuring I would go with the good stuff from the get go. Long story short the new engine was pinging and I looked for the vacuum leak forever just to find the thermostat was stuck half open. Just to give a heads up for things to expect maybe.

Bikerjr1

  • Guest
Re: thermostat
« Reply #4 on: May 20, 2009, 09:17:14 PM »
I check'em by dunking them in a pot of boiling water before I will install one.  15 min to check vs installing one only to find out it's bad is a good trade off.  Yea they ain't hard to change but that are a pain.
JR

Offline jfrabat

  • Gargantuan Mango Tree Mechanic®
  • Member
  • *
  • Posts: 3676
  • Finally USING the Jeep!
Re: thermostat
« Reply #5 on: May 21, 2009, 12:46:10 AM »
When I changed mine, I went with a 190* RObert Shaw; I did not check it (probably should have), but so far it has worked flawlessly!
'94 YJ 2.5L with 4" RE lift, Superwinch EPi9.0, FoMoCo e-Fan, SD30 and SD35 w/ARB-5.13, 165A alt., 33" BFG KM2 on 15" AR wheels, Sony sound system, Pavement Ends Hardtop, Hydroboost

DodgeMudder

  • Guest
Re: thermostat
« Reply #6 on: May 21, 2009, 08:23:50 PM »
I hate reading threads like this, my YJ is running warm, (215-225º) I changed the thermostat recently, and have been thinking I just need to flush the Rad to get it to run cooler again used to run in the 170º range, then tried to overheat so I swapped the thermostat, now it sounds like I should swap the thermo again or at least pull and check it. :brick:

john91yj

  • Guest
Re: thermostat
« Reply #7 on: May 22, 2009, 03:40:34 PM »
I've been wondering about my thermostat. As soon as I start, the temp guage maxes out. The needle on the guage used to jump around but now as soon as it's running it stays all the way to the right. Runs fine, but I'm really not too mechanical.

Offline neale_rs

  • Member
  • Posts: 3583
Re: thermostat
« Reply #8 on: May 22, 2009, 04:09:09 PM »
In your case it is most likely the sensor.  The engine cannot get hot right away.
'95 YJ, 33 x 12.5 mud tires, RE 4.5 ED lift, Atlas 4 speed, rear D44, ARBs front and rear, 4.56 gears, 8000# winch

john91yj

  • Guest
Re: thermostat
« Reply #9 on: May 23, 2009, 08:40:53 AM »
Okay, this morning I went to town and when I started up the temp was right above 210. Once I got about a mile down the road, it maxed out. If it is the sensor, where do I find that? Also, is it hard to replace?

lanulos89

  • Guest
Re: thermostat
« Reply #10 on: May 23, 2009, 03:40:18 PM »
the sensor was like 20 bucks at the dealet for me two yrs ago.  its an eaasy swap its right on the back of the head drivers side.  wanna say its like a 10 mm maybe bigger one wire sensor

Offline jfrabat

  • Gargantuan Mango Tree Mechanic®
  • Member
  • *
  • Posts: 3676
  • Finally USING the Jeep!
Re: thermostat
« Reply #11 on: May 24, 2009, 10:34:14 AM »
Okay, this morning I went to town and when I started up the temp was right above 210. Once I got about a mile down the road, it maxed out. If it is the sensor, where do I find that? Also, is it hard to replace?

Took me about 15 minutes to change mine (including the time getting the tools out)
'94 YJ 2.5L with 4" RE lift, Superwinch EPi9.0, FoMoCo e-Fan, SD30 and SD35 w/ARB-5.13, 165A alt., 33" BFG KM2 on 15" AR wheels, Sony sound system, Pavement Ends Hardtop, Hydroboost