« previous next »
Pages: 1 [2]   Go Down

Author Topic: 3,200 rpm idle!!!!  (Read 1579 times)

0 Members and 6 Guests are viewing this topic.

95yj0645

  • Guest
Re: 3,200 rpm idle!!!!
« Reply #15 on: January 04, 2011, 07:21:39 AM »
So the offset washers are specifically for the intake bolts only?
Logged

Offline sharpxmen

  • Chief Squirrel BlowerŪ
  • Member
  • *
  • Posts: 7093
Re: 3,200 rpm idle!!!!
« Reply #16 on: January 04, 2011, 09:38:45 AM »
Quote from: 95yj0645 on January 04, 2011, 07:21:39 AM
So the offset washers are specifically for the intake bolts only?

they go on the bolts which are in between exhaust and intake (but I think those are the only bolts that go on the intake if that's what you're asking). take some pics once you put them on and i'll let you know if you got it right, my mental pictures are a bit blurry since I installed the pacesetter.
Logged
'95 YJ, NSG370 6spd / Hurst shifter, Dana 300 + 4:1 Doubler / tri-stick, Custom skid, Super D35 / Auburn LSD / 4.88, 35x12.5x15 BFG KM2, 64mm t/b, 1.7 RollerRockers, MkVIII e-fan, Dual Diaph Booster
Latest: Corbeau BajaRS heated seats :dance: keeping warm the rear end

Offline dwtaylorpdx

  • Member
  • Posts: 1038
Re: 3,200 rpm idle!!!!
« Reply #17 on: January 04, 2011, 09:54:29 AM »
You should also be running the full length gasket with headers
not the one that only has intake manifold gaskets.

My 94 had no exhaust gasket at all when new. The cast iron manifold was
thicker than the intake manifold, but the intake manifold gaskets made
them the same thickness.

Dave
Logged
94 YJ - 2.5 Hesco Cam B&B Ported - AX5 Trans w/Centerforce Dual Friction Clutch - 4" Rough Country Lift W/Skyjacker Shocks - D44 Rear/ARB - D30/ARB - ARB Compressor - Warn M8000 in Custom Bumper - Reunell Rear Bumper - Metalcloak 6" Body Armor Kit - Tuffy Console - 265x85-16 Tires - 2M Radio

Offline sharpxmen

  • Chief Squirrel BlowerŪ
  • Member
  • *
  • Posts: 7093
Re: 3,200 rpm idle!!!!
« Reply #18 on: January 04, 2011, 10:43:59 AM »
Quote from: dwtaylorpdx on January 04, 2011, 09:54:29 AM
You should also be running the full length gasket with headers
not the one that only has intake manifold gaskets.

My 94 had no exhaust gasket at all when new. The cast iron manifold was
thicker than the intake manifold, but the intake manifold gaskets made
them the same thickness.

Dave

the pacesetter comes with a 1-piece gasket
Logged
'95 YJ, NSG370 6spd / Hurst shifter, Dana 300 + 4:1 Doubler / tri-stick, Custom skid, Super D35 / Auburn LSD / 4.88, 35x12.5x15 BFG KM2, 64mm t/b, 1.7 RollerRockers, MkVIII e-fan, Dual Diaph Booster
Latest: Corbeau BajaRS heated seats :dance: keeping warm the rear end

95yj0645

  • Guest
Re: 3,200 rpm idle!!!!
« Reply #19 on: January 04, 2011, 11:26:46 AM »
ok so I put a fel pro gasket on , torqued it all in sequence and used the washers in the right place and now its redlining WTF .. I would really like to talk to someone one on one maybe they could explain it better over the phone cuz im at a loss I installed everything by the book .. I unplugged the TPS and accelerator cable and still its redlining  , Im begging someone to message me there number so I can get this taken care of
Logged

95yj0645

  • Guest
Re: 3,200 rpm idle!!!!
« Reply #20 on: January 04, 2011, 11:35:50 AM »
Sharpxmen - I sent you a message with my number but idk if it went through
Logged

95yj0645

  • Guest
Re: 3,200 rpm idle!!!!
« Reply #21 on: January 04, 2011, 04:12:57 PM »
Jeep is fixed and back on the road .. my idle problem was the rear guide pin on the intake was stuck in the intake causing an 1/8" gap .. got it sealed up right and welded my exhaust back up and after I did all the mods this baby scoots I mean scoots .. I hit 80mph and it was climbing .. Iv never seen past 74
Logged

Offline sharpxmen

  • Chief Squirrel BlowerŪ
  • Member
  • *
  • Posts: 7093
Re: 3,200 rpm idle!!!!
« Reply #22 on: January 04, 2011, 05:04:35 PM »
Quote from: 95yj0645 on January 04, 2011, 04:12:57 PM
Jeep is fixed and back on the road .. my idle problem was the rear guide pin on the intake was stuck in the intake causing an 1/8" gap .. got it sealed up right and welded my exhaust back up and after I did all the mods this baby scoots I mean scoots .. I hit 80mph and it was climbing .. Iv never seen past 74

glad you got it sorted out  :thumb:
Logged
'95 YJ, NSG370 6spd / Hurst shifter, Dana 300 + 4:1 Doubler / tri-stick, Custom skid, Super D35 / Auburn LSD / 4.88, 35x12.5x15 BFG KM2, 64mm t/b, 1.7 RollerRockers, MkVIII e-fan, Dual Diaph Booster
Latest: Corbeau BajaRS heated seats :dance: keeping warm the rear end

95yj0645

  • Guest
Re: 3,200 rpm idle!!!!
« Reply #23 on: January 04, 2011, 08:33:50 PM »
Me too thanks so much for the help.. It was exactly what you said sharp
Logged
Pages: 1 [2]   Go Up
« previous next »