« previous next »
Pages: [1]   Go Down

Author Topic: Seatbelt install questions  (Read 843 times)

0 Members and 1 Guest are viewing this topic.

Complete Loser

  • Guest
Seatbelt install questions
« on: May 16, 2010, 07:48:40 PM »
Well, started installing seatbelts, then the moron bug hit me. Where the heck do i install one of the anchor points. Its not the upper roll bar point, or the clutch/reel point. Its the other one. (the part in my hand).


Im sorry the pic is sideways, but im effing tired of fixing them. I rotate them in paint when i downsize them, and then save them, and then upload to ****bucket, and its a crap shoot whether they will upload properly or sideways.  :brick:

Anyways, thanks for any help. :)  :thumbsup:
Logged

Offline sharpxmen

  • Chief Squirrel BlowerŪ
  • Member
  • *
  • Posts: 7093
Re: Seatbelt install questions
« Reply #1 on: May 16, 2010, 08:11:55 PM »
can't remember exactly how it looks over there (and i'm too lazy to go look) but from what i recall the bolt you're holding would go where you already installed the seatbelt retractor.

i'll go look and report back in a bit...
Logged
'95 YJ, NSG370 6spd / Hurst shifter, Dana 300 + 4:1 Doubler / tri-stick, Custom skid, Super D35 / Auburn LSD / 4.88, 35x12.5x15 BFG KM2, 64mm t/b, 1.7 RollerRockers, MkVIII e-fan, Dual Diaph Booster
Latest: Corbeau BajaRS heated seats :dance: keeping warm the rear end

Offline sharpxmen

  • Chief Squirrel BlowerŪ
  • Member
  • *
  • Posts: 7093
Re: Seatbelt install questions
« Reply #2 on: May 16, 2010, 08:21:49 PM »
from the pic is different from what i have (the seatbelt) - anyway, the threaded hole is on the side of the tub between the roll bar and the door opening opposite to where the seat handle is - there is a reinforcing plate there, that's where the bolt goes. My seatbelt has the end you're holding on the same bracket with the retractor and it does not come off and there is only one hole where the bolt goes in but i assume should be the same in your case (I mean you can use the same bolt hole).
« Last Edit: May 16, 2010, 08:23:01 PM by sharpxmen »
Logged
'95 YJ, NSG370 6spd / Hurst shifter, Dana 300 + 4:1 Doubler / tri-stick, Custom skid, Super D35 / Auburn LSD / 4.88, 35x12.5x15 BFG KM2, 64mm t/b, 1.7 RollerRockers, MkVIII e-fan, Dual Diaph Booster
Latest: Corbeau BajaRS heated seats :dance: keeping warm the rear end

czjeeper

  • Guest
Re: Seatbelt install questions
« Reply #3 on: May 17, 2010, 10:47:02 AM »
It bolts right next to the retractor, just forward of it.
Logged

Offline Jeffy

  • Administrator
  • Member
  • Posts: 14934
Re: Seatbelt install questions
« Reply #4 on: May 17, 2010, 01:01:19 PM »
Quote from: czjeeper on May 17, 2010, 10:47:02 AM
It bolts right next to the retractor, just forward of it.
yup.  ...on the floor.
Logged
Youtube Channel: https://www.youtube.com/channel/UCZNlr60GXH5OlKIFrT7P6mg
My Jeep: http://4bangerjp.com/forums/index.php?topic=2783.0
"If the motor car were invented today, there is absolutely no way that any government in the world would let normal members of the public drive one."

Complete Loser

  • Guest
Re: Seatbelt install questions
« Reply #5 on: May 19, 2010, 11:00:17 AM »
Yup. you are all right. I figured it out just after i posted. lol Was tired and had flash burn from a long day in the shop. I installed the retractor, and it was hiding the bolt hole on the side of the tub. lol 
For some reason, i didnt get any notifications. :( I will have to check into that.
Logged
Pages: [1]   Go Up
« previous next »