Author Topic: Rear end shimmy/vibration??  (Read 729 times)

0 Members and 1 Guest are viewing this topic.

Offline stan98tj

  • Empty Wallet Wheeling Since 2007®
  • Member
  • *
  • Posts: 1816
  • Wheeling New England
Rear end shimmy/vibration??
« on: September 17, 2010, 06:08:30 PM »
Forgive how vague my description is: Just noticed last night at low speed (under 5mph) an odd shimmy/vibration/kind of a grind coming from the vehicle. While it is doing it, it also comes with a certain slight "thud" that is more felt then heard. Pretty much a grind and vibration felt through out. Cant hear anything from outside the vehicle..but you can feel it while inside.  This is all mostly felt, you can start to kind of hear it but like i said it's all mostly felt. I took a buddy of mine in the passanger seat to see if he could  hear/feel it. we figure it feels like somewhere from center of the vehicle back...i think it may be near the rear end. I need some ideas on what to look at first. Rear driveshaft? U-Joint? wheel Bearings?
Any ideas would be greatly appreciated cause im pretty much scratching my head on this one.

BTW: when my fwd driveshaft U-joint crapped out, it made a steady clicking followed by a thud. Im not so sure it's a u-joint in this situation cause the sound doesnt have a pattern of any sorts.
thanks,
-stan
98 TJ 35"Maxxis Trep.Old Man Emu 2.5""+1"BL,IronMan Fab control arms,4.56gears,Ford 8.8+ARB,Currie/IronMan steering, WARN VR10,HP D30 sleeved+ RCV,Body Armor Rock Rails WISHLIST:TDi.Girlfriend hates it :) If you can read this don't flip me over i dont have any $$ left to fix it

Offline sharpxmen

  • Chief Squirrel Blower®
  • Member
  • *
  • Posts: 7093
Re: Rear end shimmy/vibration??
« Reply #1 on: September 19, 2010, 07:22:31 PM »
could be the driveshaft best case scenario. I kinda had the same thing happening but by the sounds of it was more obvious than yours and in my case was the R&P in the rear axle (chipped a few teeth), i hope it's the d/s in your case.
'95 YJ, NSG370 6spd / Hurst shifter, Dana 300 + 4:1 Doubler / tri-stick, Custom skid, Super D35 / Auburn LSD / 4.88, 35x12.5x15 BFG KM2, 64mm t/b, 1.7 RollerRockers, MkVIII e-fan, Dual Diaph Booster
Latest: Corbeau BajaRS heated seats :dance: keeping warm the rear end

Torch_Ind

  • Guest
Re: Rear end shimmy/vibration??
« Reply #2 on: September 19, 2010, 07:27:11 PM »
could be the driveshaft best case scenario. I kinda had the same thing happening but by the sounds of it was more obvious than yours and in my case was the R&P in the rear axle (chipped a few teeth), i hope it's the d/s in your case.

check your u-joints !!!

Offline stan98tj

  • Empty Wallet Wheeling Since 2007®
  • Member
  • *
  • Posts: 1816
  • Wheeling New England
Re: Rear end shimmy/vibration??
« Reply #3 on: September 20, 2010, 04:22:46 PM »
Turned out to be something way more simple. i had recently rotated my fwd tires back to the rear, and the rear fwd. the fwd ones had worn down badly and on an angle...when i put em on the rear they were more squared on the ground then what they had been previously so the vibrations i was feeling were due to the outer tread being deeper then the rest of the tread on the tire. swapped em back to how they were and everything was fine. Did notice a dent in my driveshaft though....gonna check the joints to make sure nothing is out of line.
98 TJ 35"Maxxis Trep.Old Man Emu 2.5""+1"BL,IronMan Fab control arms,4.56gears,Ford 8.8+ARB,Currie/IronMan steering, WARN VR10,HP D30 sleeved+ RCV,Body Armor Rock Rails WISHLIST:TDi.Girlfriend hates it :) If you can read this don't flip me over i dont have any $$ left to fix it

Offline FourbangerYJ

  • Servicing Squirrels Since 1995®
  • Member
  • *
  • Posts: 3372
Re: Rear end shimmy/vibration??
« Reply #4 on: September 20, 2010, 04:46:44 PM »
A dent  in drive shaft is a big weak spot, which could result in a twisted shaft.
Scott~

Using tools you have not used in a while is like shaking hands with old friends. :nod: