« previous next »
Pages: [1]   Go Down

Author Topic: Powertrax No-Slip Installation Help  (Read 1484 times)

0 Members and 2 Guests are viewing this topic.

redYJrider

  • Guest
Powertrax No-Slip Installation Help
« on: October 25, 2010, 01:06:07 PM »
I'm gettin ready to install a used Powertrax No-Slip into the rear of my 90YJ. I'm missing the check block though. Does anyone know the dimensions of this check block? I can't seem to get a response from Richmond Gear.    :brick:
« Last Edit: October 25, 2010, 01:07:24 PM by redYJrider »
Logged

Offline Jeffy

  • Administrator
  • Member
  • Posts: 14934
Re: Powertrax No-Slip Installation Help
« Reply #1 on: October 25, 2010, 01:18:03 PM »
Quote from: redYJrider on October 25, 2010, 01:06:07 PM
I'm gettin ready to install a used Powertrax No-Slip into the rear of my 90YJ. I'm missing the check block though. Does anyone know the dimensions of this check block? I can't seem to get a response from Richmond Gear.    :brick:
Did you try contacting the place you bought the locker from?
Logged
Youtube Channel: https://www.youtube.com/channel/UCZNlr60GXH5OlKIFrT7P6mg
My Jeep: http://4bangerjp.com/forums/index.php?topic=2783.0
"If the motor car were invented today, there is absolutely no way that any government in the world would let normal members of the public drive one."

redYJrider

  • Guest
Re: Powertrax No-Slip Installation Help
« Reply #2 on: October 25, 2010, 01:28:15 PM »
Quote from: Jeffy on October 25, 2010, 01:18:03 PM
Did you try contacting the place you bought the locker from?

Ebayer wasn't familier with it.
Logged

Offline Jeffy

  • Administrator
  • Member
  • Posts: 14934
Re: Powertrax No-Slip Installation Help
« Reply #3 on: October 25, 2010, 01:36:34 PM »
Was it used?  In any case I'd call Richmond Gears if you haven't already.  Emails don't always get checked.
Logged
Youtube Channel: https://www.youtube.com/channel/UCZNlr60GXH5OlKIFrT7P6mg
My Jeep: http://4bangerjp.com/forums/index.php?topic=2783.0
"If the motor car were invented today, there is absolutely no way that any government in the world would let normal members of the public drive one."

redYJrider

  • Guest
Re: Powertrax No-Slip Installation Help
« Reply #4 on: October 25, 2010, 01:56:26 PM »
Quote from: Jeffy on October 25, 2010, 01:36:34 PM
Was it used?  In any case I'd call Richmond Gears if you haven't already.  Emails don't always get checked.

Yes it's used. I'll try calling Richmond Gear again in a little while.
Logged

Offline chardrc

  • Member
  • Posts: 3535
Re: Powertrax No-Slip Installation Help
« Reply #5 on: October 25, 2010, 03:15:38 PM »
powertrax 92-0435-2705 for d35 1990-1993. got the same locker in my jeep pulled out the checker from the box and got these dimensions.

wide side(max allowable): 0.165 in
thin side (minimum allowable): 0.132 in

hope this helps
« Last Edit: October 25, 2010, 03:19:51 PM by chardrc »
Logged
1990 YJ 4cly, ax5, 2.5 inch BDS lift, 31 MTr\'s,  Powertrax-lockers all around, track-bars removed, boomerang shackles, warn m8000 winch, electric fan. [sold but not forgotten]

2007 jk Rubicon 2dr

redYJrider

  • Guest
Re: Powertrax No-Slip Installation Help
« Reply #6 on: October 25, 2010, 03:32:12 PM »
Quote from: chardrc on October 25, 2010, 03:15:38 PM
powertrax 92-0435-2705 for d35 1990-1993. got the same locker in my jeep pulled out the checker from the box and got these dimensions.

wide side(max allowable): 0.165 in
thin side (minimum allowable): 0.132 in

hope this helps

That's what I'm looking for. Thank you!
Logged
Pages: [1]   Go Up
« previous next »