« previous next »
Pages: [1]   Go Down

Author Topic: heater issues  (Read 2175 times)

0 Members and 1 Guest are viewing this topic.

95yjman

  • Guest
heater issues
« on: October 16, 2012, 11:49:44 PM »
The heater in my 97 TJ only works on the high setting, I replaced the resistor and it didn't change anything.  Do you think its the switch in the dash?  I checked the fuse and its good.  The fuse for this is located behind the glove box right?  Just to make sure i wasn't checking a fuse for something else.
Logged

Offline Jeffy

  • Administrator
  • Member
  • Posts: 14934
Re: heater issues
« Reply #1 on: October 17, 2012, 01:25:59 PM »
If it's not the resister then it's probably the switch.
Logged
Youtube Channel: https://www.youtube.com/channel/UCZNlr60GXH5OlKIFrT7P6mg
My Jeep: http://4bangerjp.com/forums/index.php?topic=2783.0
"If the motor car were invented today, there is absolutely no way that any government in the world would let normal members of the public drive one."

95yjman

  • Guest
Re: heater issues
« Reply #2 on: October 21, 2012, 07:36:21 PM »
Cool thanks, anybody know if it is gonna be hard to seperate the steering shaft where it bolts to mount which is bolted to the frame?  I have install my bracket that brings the steering shaft up an inch..
Logged

Offline sharpxmen

  • Chief Squirrel BlowerŪ
  • Member
  • *
  • Posts: 7093
Re: heater issues
« Reply #3 on: October 21, 2012, 07:44:30 PM »
i have a 1'' b/l and didnt install any bracket, no issues so far
Logged
'95 YJ, NSG370 6spd / Hurst shifter, Dana 300 + 4:1 Doubler / tri-stick, Custom skid, Super D35 / Auburn LSD / 4.88, 35x12.5x15 BFG KM2, 64mm t/b, 1.7 RollerRockers, MkVIII e-fan, Dual Diaph Booster
Latest: Corbeau BajaRS heated seats :dance: keeping warm the rear end

95yjman

  • Guest
Re: heater issues
« Reply #4 on: October 21, 2012, 08:03:35 PM »
yeah I was kinda on the fence about installing it. It had a 2 inch body lift on it when I bought it and didn't have one on.  I have since lowered it to a 1 inch body lift.  I didn't know if i was doing harm by not putting the new bracket on.  My steering wheel isn't centered but it never has been since I bought it.  I was figuring it was due to the steering shaft angle. May need a alinement too..
Logged

Offline sharpxmen

  • Chief Squirrel BlowerŪ
  • Member
  • *
  • Posts: 7093
Re: heater issues
« Reply #5 on: October 21, 2012, 10:41:12 PM »
when you lift it you need to adjust the drag-link to get it back in the center, probably what happened. drop pitman arm corrects the issue slightly but you still need adjustment. Unrelated to the body lift but related to the suspension lift (just to clarify what i meant by "when you lift it).
Logged
'95 YJ, NSG370 6spd / Hurst shifter, Dana 300 + 4:1 Doubler / tri-stick, Custom skid, Super D35 / Auburn LSD / 4.88, 35x12.5x15 BFG KM2, 64mm t/b, 1.7 RollerRockers, MkVIII e-fan, Dual Diaph Booster
Latest: Corbeau BajaRS heated seats :dance: keeping warm the rear end

95yjman

  • Guest
Re: heater issues
« Reply #6 on: October 22, 2012, 01:10:36 AM »
Suspension is stock, always has been. Only kind of lift this Jeep has had is body lifts..
Logged

Offline sharpxmen

  • Chief Squirrel BlowerŪ
  • Member
  • *
  • Posts: 7093
Re: heater issues
« Reply #7 on: October 22, 2012, 01:25:10 AM »
that shouldn't affect your steering wheel centering, you need to adjust it or maybe an alignment.
Logged
'95 YJ, NSG370 6spd / Hurst shifter, Dana 300 + 4:1 Doubler / tri-stick, Custom skid, Super D35 / Auburn LSD / 4.88, 35x12.5x15 BFG KM2, 64mm t/b, 1.7 RollerRockers, MkVIII e-fan, Dual Diaph Booster
Latest: Corbeau BajaRS heated seats :dance: keeping warm the rear end
Pages: [1]   Go Up
« previous next »