« previous next »
Pages: [1]   Go Down

Author Topic: steering problem  (Read 1671 times)

0 Members and 1 Guest are viewing this topic.

4X4DAVE

  • Guest
steering problem
« on: November 03, 2006, 11:58:12 AM »
About a week later after installing the engine mounts, one inch lifts, something went wrong with my steering. Not sure if related. When I try to turn its really hard then easy then hard again. It seem harder to turn left. The steering fluid level is good. Could my power steering pump be going out? What should I check, and how. I think that its getting worse over time.

Thanks
Logged

Offline Jeffy

  • Administrator
  • Member
  • Posts: 14934
Re: steering problem
« Reply #1 on: November 03, 2006, 12:46:38 PM »
Quote from: "4X4DAVE"
About a week later after installing the engine mounts, one inch lifts, something went wrong with my steering. Not sure if related. When I try to turn its really hard then easy then hard again. It seem harder to turn left. The steering fluid level is good. Could my power steering pump be going out? What should I check, and how. I think that its getting worse over time.

Thanks


Well, I'd first check the arms for any bends.  Take the steering stabilizer off and try driving it.  It could be that the stabilizer is damaged. In which case it would be a cheap fix.
Logged
Youtube Channel: https://www.youtube.com/channel/UCZNlr60GXH5OlKIFrT7P6mg
My Jeep: http://4bangerjp.com/forums/index.php?topic=2783.0
"If the motor car were invented today, there is absolutely no way that any government in the world would let normal members of the public drive one."

4X4DAVE

  • Guest
steering problem
« Reply #2 on: November 03, 2006, 02:00:52 PM »
I will look tonight and hopefully a cheap fix, thanks
Logged

YJmechanic

  • Guest
steering problem
« Reply #3 on: November 03, 2006, 03:09:37 PM »
good place to start jeffy,  also your gearbox may be binding internally.
Logged

4X4DAVE

  • Guest
steering problem
« Reply #4 on: November 06, 2006, 07:52:47 AM »
I took my steering stabalizer off and it still felt the same. So, how do I check the steering box? And would I have to replace the whole thing?

I found a power steering gearbox on ebay for $27, but it ends in 8 hours, not sure if I should get it just because I don't think I could find one cheaper. Any advice would be nice
Logged

Offline Jeffy

  • Administrator
  • Member
  • Posts: 14934
steering problem
« Reply #5 on: November 06, 2006, 10:30:04 AM »
Quote from: "4X4DAVE"
I took my steering stabalizer off and it still felt the same. So, how do I check the steering box? And would I have to replace the whole thing?

I found a power steering gearbox on ebay for $27, but it ends in 8 hours, not sure if I should get it just because I don't think I could find one cheaper. Any advice would be nice


You can probably jack the front off the ground then turn the wheel.  Disconnect the drag-link and turn it again.  Then disconnect the steering rod at the end of the column and try turning it.  This should help you localize the problem.
Logged
Youtube Channel: https://www.youtube.com/channel/UCZNlr60GXH5OlKIFrT7P6mg
My Jeep: http://4bangerjp.com/forums/index.php?topic=2783.0
"If the motor car were invented today, there is absolutely no way that any government in the world would let normal members of the public drive one."

YJmechanic

  • Guest
steering problem
« Reply #6 on: November 08, 2006, 07:15:30 PM »
jeffy is dead on.  and you won't find it cheaper than that.
Logged

SGT_Tirrell

  • Guest
steering problem
« Reply #7 on: November 27, 2006, 03:47:48 PM »
I had a similar problem on my old AMC and it turned out to be the steering box.  Not sure if this helps you, but it took me a while to figure it out.  I just changed the box and voila! no more binding.
Logged
Pages: [1]   Go Up
« previous next »