« previous next »
Pages: 1 2 [3] 4 5 ... 7   Go Down

Author Topic: Issues with 19# injector swap  (Read 9912 times)

0 Members and 7 Guests are viewing this topic.

YJ KiD

  • Guest
Re: Issues with 19# injector swap
« Reply #30 on: October 17, 2009, 03:16:12 PM »
i guess what i was trying to get at was that there are no more mods or changes that need to be made for the swap to compensate for the extra fuel being delivered.  Sorry didn't explai it very well.

didn't end up doing it today, cant control the weather
Logged

Offline Jeffy

  • Administrator
  • Member
  • Posts: 14934
Re: Issues with 19# injector swap
« Reply #31 on: October 17, 2009, 03:24:48 PM »
Quote from: YJ KiD on October 17, 2009, 03:16:12 PM
i guess what i was trying to get at was that there are no more mods or changes that need to be made for the swap to compensate for the extra fuel being delivered.  Sorry didn't explai it very well.

didn't end up doing it today, cant control the weather
Is that going to be your only mod?
Logged
Youtube Channel: https://www.youtube.com/channel/UCZNlr60GXH5OlKIFrT7P6mg
My Jeep: http://4bangerjp.com/forums/index.php?topic=2783.0
"If the motor car were invented today, there is absolutely no way that any government in the world would let normal members of the public drive one."

Offline FourbangerYJ

  • Servicing Squirrels Since 1995®
  • Member
  • *
  • Posts: 3372
Re: Issues with 19# injector swap
« Reply #32 on: October 17, 2009, 04:05:46 PM »
Well, I took it out for a drive. It started out running good. Pulled a hill that normally bogged the motor. Seemed like it had good power. Then it had a shudder at about 3K RPM's. It got worse. Then it would not go above 2500 RPM, it sounded like junk! Then is seemed to clear up ran good for about 2 seconds and started to run like crap.
Looks like I am going to pull those injectors and install the other set I have.  :baby: Good thing it's a pretty easy job.
Logged
Scott~

Using tools you have not used in a while is like shaking hands with old friends. :nod:

Offline FourbangerYJ

  • Servicing Squirrels Since 1995®
  • Member
  • *
  • Posts: 3372
Re: Issues with 19# injector swap
« Reply #33 on: October 17, 2009, 04:26:48 PM »
Thinking about it for a bit. The trouble started after the CEL came on. I wonder if those 2 broken clips are for some reason not making a good enough contact and are not firing the injector? They seem tight.
Logged
Scott~

Using tools you have not used in a while is like shaking hands with old friends. :nod:

Offline Jeffy

  • Administrator
  • Member
  • Posts: 14934
Re: Issues with 19# injector swap
« Reply #34 on: October 17, 2009, 05:42:47 PM »
Quote from: FourbangerYJ on October 17, 2009, 04:26:48 PM
Thinking about it for a bit. The trouble started after the CEL came on. I wonder if those 2 broken clips are for some reason not making a good enough contact and are not firing the injector? They seem tight.
What codes?  25?
Logged
Youtube Channel: https://www.youtube.com/channel/UCZNlr60GXH5OlKIFrT7P6mg
My Jeep: http://4bangerjp.com/forums/index.php?topic=2783.0
"If the motor car were invented today, there is absolutely no way that any government in the world would let normal members of the public drive one."

Offline sharpxmen

  • Chief Squirrel Blower®
  • Member
  • *
  • Posts: 7093
Re: Issues with 19# injector swap
« Reply #35 on: October 17, 2009, 06:49:28 PM »
Quote from: FourbangerYJ on October 17, 2009, 04:26:48 PM
Thinking about it for a bit. The trouble started after the CEL came on. I wonder if those 2 broken clips are for some reason not making a good enough contact and are not firing the injector? They seem tight.

take the rail out and have 4  jars under the injectors (or 2 bigger ones since the 1-2 and 3-4 cyl are close enough). unplug your ignition coil and have someone crank the engine while you watch the spray coming out of the injectors - could be that one or 2 of them is/are squirting rather than misting fuel and the symptom is somewhat similar to when they are unplugged. I would also check the plugs and see if any of them are wet or really black. 
Logged
'95 YJ, NSG370 6spd / Hurst shifter, Dana 300 + 4:1 Doubler / tri-stick, Custom skid, Super D35 / Auburn LSD / 4.88, 35x12.5x15 BFG KM2, 64mm t/b, 1.7 RollerRockers, MkVIII e-fan, Dual Diaph Booster
Latest: Corbeau BajaRS heated seats :dance: keeping warm the rear end

Offline FourbangerYJ

  • Servicing Squirrels Since 1995®
  • Member
  • *
  • Posts: 3372
Re: Issues with 19# injector swap
« Reply #36 on: October 17, 2009, 08:10:53 PM »
Well, I swapped in the other set. Runs the same as with the first set.
I have not checked the code. I am guessing it's the F.I. connector.
I thought about pulling the spark plug to see what's going on.
Good idea on the pulling the rail and coil wire.
Logged
Scott~

Using tools you have not used in a while is like shaking hands with old friends. :nod:

YJake

  • Guest
Re: Issues with 19# injector swap
« Reply #37 on: October 17, 2009, 08:18:07 PM »
Just got my refurbed Gen-2 19lbs. Injectors in the mail yesterday.

Not sure that I wan't to put them in yet since I'll be going on a trip in less than two weeks.

I have the 4.0TB and have removed the airbox restrictors. I hope that is enough for the injectors to be used to their full extent.
Logged

Offline FourbangerYJ

  • Servicing Squirrels Since 1995®
  • Member
  • *
  • Posts: 3372
Re: Issues with 19# injector swap
« Reply #38 on: October 17, 2009, 08:27:00 PM »
Quote from: Jeffy on October 17, 2009, 05:42:47 PM
What codes?  25?

12 and 27. I know what 27 is, it's the FI control. What's 12?
Logged
Scott~

Using tools you have not used in a while is like shaking hands with old friends. :nod:

Offline aw12345

  • Member
  • Posts: 3065
    • my jeep picture page
Re: Issues with 19# injector swap
« Reply #39 on: October 17, 2009, 09:01:50 PM »
Scott, I have a little pulser box so you can pulse the injectors individually and see what the pressure drop for each one is. Is about the best way to test the injectors.
Some auto parts stores carry the tool also. It's the easiest way to see how much fuel each injector flows. In general broken clips on a injector wire connector does not generally cause a misfire
Logged
2006 Jeep Wrangler TJ SE
2004 Jeep Wrangler TJ SE

Offline dwtaylorpdx

  • Member
  • Posts: 1038
Re: Issues with 19# injector swap
« Reply #40 on: October 17, 2009, 10:11:13 PM »
12 = Lean condition + MAP low vacume signal if I recall from my hell trip a couple weeks ago...

Dave
Logged
94 YJ - 2.5 Hesco Cam B&B Ported - AX5 Trans w/Centerforce Dual Friction Clutch - 4" Rough Country Lift W/Skyjacker Shocks - D44 Rear/ARB - D30/ARB - ARB Compressor - Warn M8000 in Custom Bumper - Reunell Rear Bumper - Metalcloak 6" Body Armor Kit - Tuffy Console - 265x85-16 Tires - 2M Radio

Offline Jeffy

  • Administrator
  • Member
  • Posts: 14934
Re: Issues with 19# injector swap
« Reply #41 on: October 18, 2009, 12:33:37 AM »
Quote from: FourbangerYJ on October 17, 2009, 08:10:53 PM
Well, I swapped in the other set. Runs the same as with the first set.
I have not checked the code. I am guessing it's the F.I. connector.
I thought about pulling the spark plug to see what's going on.
Good idea on the pulling the rail and coil wire.
http://4bangerjp.com/forums/index.php/topic,3419.0.html

Disconnected battery
Logged
Youtube Channel: https://www.youtube.com/channel/UCZNlr60GXH5OlKIFrT7P6mg
My Jeep: http://4bangerjp.com/forums/index.php?topic=2783.0
"If the motor car were invented today, there is absolutely no way that any government in the world would let normal members of the public drive one."

Offline dwtaylorpdx

  • Member
  • Posts: 1038
Re: Issues with 19# injector swap
« Reply #42 on: October 18, 2009, 12:38:26 AM »
Ah I was thinking of 13... It wasn't in my freeking haynes manual, had to call a dealer to get it... arrg.

Dave
Logged
94 YJ - 2.5 Hesco Cam B&B Ported - AX5 Trans w/Centerforce Dual Friction Clutch - 4" Rough Country Lift W/Skyjacker Shocks - D44 Rear/ARB - D30/ARB - ARB Compressor - Warn M8000 in Custom Bumper - Reunell Rear Bumper - Metalcloak 6" Body Armor Kit - Tuffy Console - 265x85-16 Tires - 2M Radio

Offline FourbangerYJ

  • Servicing Squirrels Since 1995®
  • Member
  • *
  • Posts: 3372
Re: Issues with 19# injector swap
« Reply #43 on: October 18, 2009, 12:34:06 PM »
I pulled all 4 spark plugs. They look good. Not gassy or black. They were a light brown/reddish color.
Gonna pull the fuel rail again, maybe the injectors are not seated all the way in?
Logged
Scott~

Using tools you have not used in a while is like shaking hands with old friends. :nod:

Offline Jeffy

  • Administrator
  • Member
  • Posts: 14934
Re: Issues with 19# injector swap
« Reply #44 on: October 18, 2009, 12:36:07 PM »
Quote from: FourbangerYJ on October 18, 2009, 12:34:06 PM
I pulled all 4 spark plugs. They look good. Not gassy or black. They were a light brown/reddish color.
Gonna pull the fuel rail again, maybe the injectors are not seated all the way in?
If the rail bolted down then they are seated.
Logged
Youtube Channel: https://www.youtube.com/channel/UCZNlr60GXH5OlKIFrT7P6mg
My Jeep: http://4bangerjp.com/forums/index.php?topic=2783.0
"If the motor car were invented today, there is absolutely no way that any government in the world would let normal members of the public drive one."
Pages: 1 2 [3] 4 5 ... 7   Go Up
« previous next »