« previous next »
Pages: [1]   Go Down

Author Topic: Outboarding shocks... On a YJ  (Read 1689 times)

0 Members and 2 Guests are viewing this topic.

Offline TahoeYJ

  • Member
  • Posts: 530
  • How can I reech theese kids?
Outboarding shocks... On a YJ
« on: December 30, 2009, 10:16:11 AM »
Been following this thread on JF for the past few days

http://www.jeepforum.com/forum/f9/outboarding-rear-shocks-upper-spring-bucket-relocation-929056/

It seems like it'd be much easier to do this on a YJ than a TJ. I lost a lot of up travel when I put my 9" in, and even after adding the MORE rear brackets at the frame I still don't have the same as I did before the swap. I get bored and always want a new project to do on my Heep and this could be fun, and a learning experience. Still kind of skeptical about cutting into the frame... But it appears others haven't had issue?

I'm not necessarily going to to this, but I figured I'd see what yous' guys' think  :doggy:
Logged
92 YJ. Lifted, 4:88's, 9" rear, 4 wheel disks, some armor, some audio, 35" KM2's, and more

Offline chardrc

  • Member
  • Posts: 3535
Re: Outboarding shocks... On a YJ
« Reply #1 on: December 30, 2009, 10:39:42 AM »
looks interesting.. only thing with a yj is that your welds for teh new shock tower are going to be more critical since you have half of the load form the leaf springs connecting to the frame behind the shock tower unlike the tjs that have all the load in front of the shock tower.
Logged
1990 YJ 4cly, ax5, 2.5 inch BDS lift, 31 MTr\'s,  Powertrax-lockers all around, track-bars removed, boomerang shackles, warn m8000 winch, electric fan. [sold but not forgotten]

2007 jk Rubicon 2dr

Torch_Ind

  • Guest
Re: Outboarding shocks... On a YJ
« Reply #2 on: December 30, 2009, 12:04:37 PM »
I really like that guys front fenders
Logged

Jesse-James

  • Guest
Re: Outboarding shocks... On a YJ
« Reply #3 on: December 30, 2009, 03:21:11 PM »
Rear in mine is linked with the MORE extensions and raised lower mounts and I have no issue with shock length. Hard to believe you could have an issue with leaf springs.

Logged

Offline aw12345

  • Member
  • Posts: 3065
    • my jeep picture page
Re: Outboarding shocks... On a YJ
« Reply #4 on: December 30, 2009, 05:39:12 PM »
The front fenders are rev111 now produced by metal cloak, I believe they are available for a YJ also
Logged
2006 Jeep Wrangler TJ SE
2004 Jeep Wrangler TJ SE

Offline Jeffy

  • Administrator
  • Member
  • Posts: 14934
Re: Outboarding shocks... On a YJ
« Reply #5 on: December 30, 2009, 08:38:14 PM »
Quote from: aw12345 on December 30, 2009, 05:39:12 PM
The front fenders are rev111 now produced by metal cloak, I believe they are available for a YJ also
Hmmm, I thought Metal Cloak was the product line and Rev111 was the maker.
Logged
Youtube Channel: https://www.youtube.com/channel/UCZNlr60GXH5OlKIFrT7P6mg
My Jeep: http://4bangerjp.com/forums/index.php?topic=2783.0
"If the motor car were invented today, there is absolutely no way that any government in the world would let normal members of the public drive one."

Torch_Ind

  • Guest
Re: Outboarding shocks... On a YJ
« Reply #6 on: December 31, 2009, 10:20:25 AM »
Quote from: Jeffy on December 30, 2009, 08:38:14 PM
Hmmm, I thought Metal Cloak was the product line and Rev111 was the maker.

thanks to the both of you for the name I found them online. they are very nice!!
Logged

Offline TahoeYJ

  • Member
  • Posts: 530
  • How can I reech theese kids?
Re: Outboarding shocks... On a YJ
« Reply #7 on: December 31, 2009, 12:25:26 PM »
Quote from: Jesse-James on December 30, 2009, 03:21:11 PM
Rear in mine is linked with the MORE extensions and raised lower mounts and I have no issue with shock length. Hard to believe you could have an issue with leaf springs.


The lower mounts are much higher than they were on the D35. From the rear of the Jeep you can't see anything hanging below the axle tubes. I've flexed my junk out on the retaining wall in my dads front yard (mall crawlin' foo  :twofingers:), which is about 22-24", I've still got about 2.5-3" before I rub and the rear shocks have around 1" travel before they're fully compressed. I don't want to go to a shorter shock, so the only other option would be different mounts, mounted slightly lower on the axle tubes...
Logged
92 YJ. Lifted, 4:88's, 9" rear, 4 wheel disks, some armor, some audio, 35" KM2's, and more

Jesse-James

  • Guest
Re: Outboarding shocks... On a YJ
« Reply #8 on: December 31, 2009, 12:34:19 PM »
Sounds like a tad shorter shock is the way to go. Again my rear lower mounts are raised as well. Doesn't hurt my flex at all. I'd triangulate them before hacking the frame up. Unless you want to do it "just to do it"


My lower mounts


..and a flex shot.
Logged

Offline FourbangerYJ

  • Servicing Squirrels Since 1995®
  • Member
  • *
  • Posts: 3372
Re: Outboarding shocks... On a YJ
« Reply #9 on: December 31, 2009, 12:41:06 PM »
Quote from: Jesse-James on December 31, 2009, 12:34:19 PM

My lower mounts


..and a flex shot.


 :bow: Looks good,
Logged
Scott~

Using tools you have not used in a while is like shaking hands with old friends. :nod:
Pages: [1]   Go Up
« previous next »